- Pen kits
- Pen kit bushes
- Pen blanks
- Marlas Feathers pen blanks
- DiamondCast pen blanks
- Silver series pen blanks
- Radiance Series pen blanks
- Divine Island pen blanks
- Gilbert House pen blanks
- Crafted Makes Spangle series pen blanks
- Crafted Makes Braided series pen blanks
- Crafted Makes Carbon Fibre series pen blanks
- Blankwerks abalone pen blanks
- Flower Girl pen blanks
- Alternative natural pen blanks
- GPS Ranger pen blanks
- Alternative semi-precious pen blanks
- GPS California polyester series
- Kirinite acrylic collection
- Kirinite Ice series
- Kirinite Pearl series
- Kirinite Stardust Glitter series
- Minerva Acrylics
- Chestnut acrylic collection
- Cullinore Acrylique - acrylic pen blanks
- Semplicita SHDC pen blanks
- Semplicita Nastro pen blanks
- Ebonite pen blanks
- Wood pen blanks
- Pen blanks - reduced to clear
- Marlas Feathers pen blanks
- Bowl blanks, Spindle blanks & Project blanks
- Fountain pen nibs
- Understanding fountain pen nibs & choosing the right one
- Bock standard size 6 nibs (type 250)
- Bock standard size 5 nibs (type 180)
- Beaufort standard size 5 nibs
- Bock short body size 5 nibs (type 060)
- Bock wide shoulder size 5 nibs (type 076)
- Bock standard size 8 nibs (type 380)
- Bock calligraphy (italic) nibs
- Bock twin point calligraphy nibs (type 020)
- Bock 14k music nibs
- Left handed Bock nibs
- Bock ready-made nib sections
- Refillable rollerball nibs
- Understanding fountain pen nibs & choosing the right one
- Fountain pen ink
- Pen Refills
- Pen presentation - Boxes, pouches & display stands
- Writing accessories
- Pen making tools & drill bits
- Thread taps and dies
- Kitless pen making - tools and supplies for custom pens and bespoke pens
- Tutorial - An introduction to custom pen making
- Collets & collet chuck sets
- Keyless drill chucks
- Tailstock die holders
- Tailstock tap holders
- Morse taper lathe centres
- Triple lead thread taps and dies for pen caps
- Section sleeves and thread sleeves for kitless pens
- Mandrels for kitless pens and custom pen making
- Single lead thread taps and dies for pen components
- Thread taps for Bock fountain pen nib housings
- Thread taps for Bock ready made nib sections
- Thread taps for kitless pen rollerball nibs
- Bock ready-made fountain pen nib sections
- Clips for kitless pens
- Refillable rollerball nibs for kitless pens
- Drill bits
- Threadable pen blanks for kitless and custom pens
- Lubricant for pen makers
- Tutorial - An introduction to custom pen making
- Starbond CA superglue
- Abrasives, steel wool, finishing & polishing
- Beall Wood Buff buffing system
- Versachuck wood lathe chucks
- Lathe faceplates, micro-chucks and spindle adaptors
- Super Nova1 chuck key
- Pen tubes, springs & spares
- Mechanisms, ink converters & pencil inserts
- Bock ready-made nib sections
- Clips for kitless pens
- Casting moulds
- Shield Technology - lubrication and rust prevention
- Special offers & clearance
Collets & collet chuck sets
Collets deliver an extremely accurate workpiece and tool holding solution for kitless pens and custom pen making, and in a morse taper collet chuck they can be used at either end of the lathe. They compress to form a perfect circle at a given diameter over the full length of the collet, and although more expensive than a drill chuck, a set of collets will provide far more versatility and precision. They are much more gentle on the workpiece too.
Denoted by an ER number, collets are made in various standard sizes, which fit in a collet chuck that has the same number. The ER number defines the length and outside diameter of the collet, and within each ER size, the range of inside diameters available is also defined. In other words, the ER size dictates the minimum and maximum diameter of the workpiece or tool that you will be able to hold.
