- Pen kits
- Bushes for pen kits
- Pen blanks
- Marlas Feathers pen blanks
- DiamondCast pen blanks
- DC Silver Series pen blanks
- DC Radiance Series pen blanks
- Divine Island pen blanks
- Gilbert House pen blanks
- Crafted Makes Spangle Series pen blanks
- Crafted Makes Braided Series pen blanks
- Crafted Makes Carbon Fibre series pen blanks
- Blankwerks abalone pen blanks
- Flower Girl pen blanks
- GPS Alternative Natural pen blanks
- GPS Ranger pen blanks
- GPS Alternative Semi-Precious pen blanks
- GPS California series pen blanks
- Kirinite acrylic pen blank collection
- Kirinite Ice series pen blanks
- Kirinite Pearl series pen blanks
- Kirinite Stardust Glitter series pen blanks
- Minerva Acrylics pen blanks
- Cullinore Acrylique - Spellbinder pen blanks
- Cullinore Acrylique - acrylic pen blanks
- Chestnut acrylic pen blank collection
- Semplicita SHDC pen blanks
- Semplicita Nastro pen blanks
- Ebonite pen blanks
- Wood pen blanks
- Choose pen blanks by colour
- Pen blanks - reduced to clear
- Marlas Feathers pen blanks
- Bowl blanks, spindle blanks & project blanks
- Fountain pen nibs
- Understanding nibs and choosing the right one
- Bock standard size 6 fountain pen nibs (type 250)
- Bock standard size 5 fountain pen nibs (type 180)
- Beaufort standard size 5 fountain pen nibs
- Bock short body #5 fountain pen nibs (type 060)
- Bock wide shoulder #5 fountain pen nibs (type 076)
- Bock standard size 8 fountain pen nibs (type 380)
- Calligraphy (italic) fountain pen nibs
- Bock twin point #5 fountain pen nibs (type 020)
- Music nibs
- Left handed fountain pen nibs
- Non-engragved fountain pen nibs
- Ready made section sleeves for kitless pens
- Ready made nib sections for kitless pens
- Refillable rollerball nibs for kitless pens
- Understanding nibs and choosing the right one
- Fountain pen ink
- Pen refills
- Pen presentation - pen boxes, pen pouches & pen stands
- Writing accessories
- Pen making tools & drill bits
- Pen tubes, springs & spares
- Mechanisms, ink converters & pencil inserts
- Ready-made nib sections and section sleeves
- Clips for kitless pens
- Thread taps and dies
- Kitless pen making - tools and supplies for custom pens & bespoke pens
- Tutorial - An introduction to custom pen making
- Collets & collet chuck sets
- Keyless drill chucks
- Engineering micro-chucks
- Tailstock die holders
- Tailstock tap holders
- Morse taper lathe centres
- Triple lead thread taps and dies for pen caps
- Section sleeves and thread sleeves for kitless pens
- Mandrels for kitless pens and custom pen making
- Single lead thread taps and dies for pen components
- Thread taps for Bock fountain pen nib housings
- Thread taps for Bock ready made nib sections
- Thread taps for kitless pen rollerball nibs
- Bock ready-made fountain pen nib sections
- Clips for kitless pens
- Refillable rollerball nibs for kitless pens
- Drill bits
- Threadable pen blanks for kitless and custom pens
- Lubricant for pen makers
- Tutorial - An introduction to custom pen making
- Casting moulds for pen blanks
- Starbond CA superglue
- Abrasives, steel wool, finishing & polishing
- Beall Wood Buff buffing system
- Versachuck wood lathe chucks
- Lathe faceplates, micro-chucks and spindle adaptors
- Shield Technology - lubrication and rust prevention
- Super Nova1 chuck key
- Special offers & clearance
Pen turning
Fountain pen nibs
Fountain pen ink
Pen blanks
Mandrels for kitless pens and custom pen making
Made from solid brass, the 15mm rear tenon can be held on the lathe in a collet chuck, an engineering chuck, a drill chuck or a wood lathe chuck. Once the pen component is drilled and threaded, it can be held securely and accurately on the mandrel in order to turn and finish its outside profile.
Section mandrels are reversible and therefore able to hold the section by either its internal thread or its external thread.
Made from solid brass, the 15mm rear tenon can be held on the lathe in a collet chuck, an engineering chuck, a drill chuck or a wood lathe chuck. Once the pen component is drilled and threaded, it can be held securely and accurately on the mandrel in order to turn and finish its outside profile.
Section mandrels are reversible and therefore able to hold the section by either its internal thread or its external thread.
Made from solid brass, the 15mm rear tenon can be held on the lathe in a collet chuck, an engineering chuck, a drill chuck or a wood lathe chuck. Once the pen component is drilled and threaded, it can be held securely and accurately on the mandrel in order to turn and finish its outside profile.
Section mandrels are reversible and therefore able to hold the section by either its internal thread or its external thread.
