- Pen kits
- Pen kit bushes
- Pen blanks
- Marlas Feathers pen blanks
- DiamondCast pen blanks
- Silver series pen blanks
- Radiance Series pen blanks
- Divine Island pen blanks
- Gilbert House pen blanks
- Crafted Makes Spangle series pen blanks
- Crafted Makes Braided series pen blanks
- Crafted Makes Carbon Fibre series pen blanks
- Blankwerks abalone pen blanks
- Flower Girl pen blanks
- Alternative natural pen blanks
- GPS Ranger pen blanks
- Alternative semi-precious pen blanks
- GPS California polyester series
- Kirinite acrylic collection
- Kirinite Ice series
- Kirinite Pearl series
- Kirinite Stardust Glitter series
- Minerva Acrylics
- Chestnut acrylic collection
- Cullinore Acrylique - acrylic pen blanks
- Semplicita SHDC pen blanks
- Semplicita Nastro pen blanks
- Ebonite pen blanks
- Wood pen blanks
- Pen blanks - reduced to clear
- Marlas Feathers pen blanks
- Bowl blanks, Spindle blanks & Project blanks
- Fountain pen nibs
- Understanding fountain pen nibs & choosing the right one
- Bock standard size 6 nibs (type 250)
- Bock standard size 5 nibs (type 180)
- Beaufort standard size 5 nibs
- Bock short body size 5 nibs (type 060)
- Bock wide shoulder size 5 nibs (type 076)
- Bock standard size 8 nibs (type 380)
- Bock calligraphy (italic) nibs
- Bock twin point calligraphy nibs (type 020)
- Bock 14k music nibs
- Left handed Bock nibs
- Bock ready-made nib sections
- Refillable rollerball nibs
- Understanding fountain pen nibs & choosing the right one
- Fountain pen ink
- Pen Refills
- Pen presentation - Boxes, pouches & display stands
- Writing accessories
- Pen making tools & drill bits
- Thread taps and dies
- Kitless pen making - tools and supplies for custom pens and bespoke pens
- Tutorial - An introduction to custom pen making
- Collets & collet chuck sets
- Keyless drill chucks
- Tailstock die holders
- Tailstock tap holders
- Morse taper lathe centres
- Triple lead thread taps and dies for pen caps
- Section sleeves and thread sleeves for kitless pens
- Mandrels for kitless pens and custom pen making
- Single lead thread taps and dies for pen components
- Thread taps for Bock fountain pen nib housings
- Thread taps for Bock ready made nib sections
- Thread taps for kitless pen rollerball nibs
- Bock ready-made fountain pen nib sections
- Clips for kitless pens
- Refillable rollerball nibs for kitless pens
- Drill bits
- Threadable pen blanks for kitless and custom pens
- Lubricant for pen makers
- Tutorial - An introduction to custom pen making
- Starbond CA superglue
- Abrasives, steel wool, finishing & polishing
- Beall Wood Buff buffing system
- Versachuck wood lathe chucks
- Lathe faceplates, micro-chucks and spindle adaptors
- Super Nova1 chuck key
- Pen tubes, springs & spares
- Mechanisms, ink converters & pencil inserts
- Bock ready-made nib sections
- Clips for kitless pens
- Casting moulds
- Shield Technology - lubrication and rust prevention
- Special offers & clearance
Triple lead thread taps and dies for pen caps
Ideal for custom pens, or so called kitless pens, triple lead taps and dies cut a thread that engages in 3 separate starting positions. They are used for the cap thread of fountain pens and rollerballs to allow the cap to screw on and off with fewer turns than a thread with a single starting position.
Whereas a thread that starts in only one position will take several twists of the cap to remove it, a triple start thread will achieve it in one or two, which is a highly desirable feature in a capped pen.
Made specially for us from M2 HSS steel by TapCo, the globally acclaimed precision thread cutting specialists, our split dies are paired with a matching intermediate (US - plug) tap, and with care will last a lifetime.
We also have corresponding plug (US - bottoming) taps for several of the sizes of we offer, which are available to buy separately. If the cap you're making is opaque, a plug (bottoming) tap will usually not be required, but if the material is translucent or clear, the thread will be visible from the outside - a plug (bottoming) tap will allow the thread to be cut with a clean stop to it.
Be sure to order the correct taps though. You need to know that thread taps are named differently depending on where you live:
UK starter = US taper
UK intermediate = US plug
UK plug = US bottoming
